Hole is 3/8", for most Switchcraft type jacks. Works well with the Switchcraft J-11 1/4" jacks Similar in style to vintage Fender™ jack plates. JACK PLATE, BLACK METAL, SINGLE 1/4" JACK, 2" OUTSIDE DIAMETER. This is a tough, durable 1.2mm Black Oxide SteelĪlso included are four #8 x 3/4" black mounting screws. Does NOT fit the SW-650, SW-701, or SW-206 switches Does NOT fit the TSL/DSL amps in the JCM2000 Is smaller than the original round switch cap from Marshall™ found on some of Round caps used on the Gallien-Krueger 400RB-II, 700RB-II, 1001RB and similar models.įits push switches with actuator shaft of 2.7mm square. This is a black 5mm (approx 3/16") diameter X 9mm long switch cap which fits the SW-212Īnd 090-0012-0 Push Switches. Original Fender™ part number 0028104000.Īlso fits the Gallien-Krueger MB150E amp. Used on channel control and drive boost switches on theįront panel of the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Bluesĭeville, Blues Junior. See either the K-212 or the K-058, depending on the amplifier model. Original Gallien-Krueger part number 090-0012-0. The front panel of the 400RB-II, 400RB-III, 400RB-IV, 700RB-II, 1001RB-II, the MicroBass Series, Backline 110, Backline 112, Backline 115, Backline 210,Īnd Backline 350 G-K amps. Includes nut and washer.Ħ electrical terminals on bottom of switch (DPDT). ![]() Same as the J-12A jack, but with longer (3/8") threaded bushing for mounting in thicker panels. (SHORTING), WIRED, Switchcraft ™, LONG BUSHING JACK, 1/4", MONO, CLOSED CIRCUIT (SHORTING), WIRED, Switchcraft ™įound in vintage Fender ™ (and other) amps as the input jack.Īlso used in the Hot Rod Deluxe/Deville, Blues Deluxe/Deville as the main JACK, 1/4", MONO, OPEN CIRCUIT, WIRED, Switchcraft ™įound in many guitars, effects pedals, amps speaker output. Genuine Switchcraft™ nut and washer set for the J-563 jack. Reuse existing nut or order nut separately as part #JNUT-38, Nut & Washer NOT included - reuse original, or order JNUT-38.Īnd Gallien-Krueger ™. Models (including the G-K Backline 210 and some of the G-K RB series, such as JACK, 1/4", MONO 4-PIN, PC MOUNT, Gallien-Krueger ™ AMPS Order the PNW-16 nut found in this section) Life, and help prevent "scratchy pots" in later life.ĭownload cross-reference guide for these pots. The dust caps seal out dust for reliability, longer These pots areĪvailable with optional dust caps installed. ![]() Diameter of the body of the pot is slightly smaller than a dime. Note: These pots do not fit all G-K amps.Ĭompare carefully with the photo, or inquire if unsure. PC board circuitry, including the 700RB, 800RB and 1000RB (original series from the Used in many Gallien-Krueger ™ amp models with PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING "break-through" and adds overall durability. Ideal for amp heads, combo amps, or smaller speaker cabinets. (wide end) x 3/4" diameter (narrow end) x 0.85" tall. Ideal for rack-mount amps, combo amps, or small speaker cabinets. MEDIUM BLACK TAPERED RUBBER FEET, SET OF 4. ![]() The integral metal washer in the mounting hole helps prevent mounting screw Ideal for large rack cabinets or speaker cabinets. This heavy-duty rubber foot offers a sure grip With built-in lock washer to keep the screwĪnd nut from loosening. Used to connect a ground wire to a screw and nut on a chassis. Made from tin-plated brass - will not rust.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |